Home Applications turnkey contract Key Milestones Exports
  • PICTURES
    		•  Enquiry Contact us   A Trusted Name in Pumps 1946's

    Vertical Turbine Pumps

    Propeller Pumps

    Horizontal Split

    Pump Details
    Coverage Chart
    O & M Manual

    Non Clog Pumps

    End Suction Pumps

    Fire Fighting

    Multi Stage Centrifugal

    Ash Slurry Pumps

    Submersible Pumps

    Hydro Turbines

    Mineral Processing

    Retro Fit

     
     

    Content on this page requires a newer version of Adobe Flash Player.

    Get Adobe Flash player
     
    CONSTRUCTION FEATURES:
    • • Centerline (self-venting) discharge

    • • Back pull out design

    • • Impellers offers optimum effeciency and low NPSH
    Range Capacity : 9,000M3/hr Head :170 Mtrs
    Options
    • • CI or bronze or SS impeller & other materials

    • • Semi open and enclosed impellers

    • • Grease or oil lubrication

      • •
    • Frame mounted, biltogether

    End Suction : 50 mm to 900 mm DISCHARGE SIZE Flowmore has an entire line of heavy-duty trouble-free End -suction type Centrifugal pumps which allows selection of a suitable model for practically any demand. Highest precision standards and specialised up to date manufacturing methods, are combined to produce FLOWMORE pumps of quality and complete dependability.
    The exclusive and valuable features of these pumps, provide long and trouble free service. They contain minimum number of parts there by reducing maintenance problems. The shaft, impeller or gland - all FLOWMORE pump parts, have been engineered to give extra service and performance with greater reliability.
    Casing : The one - piece volute is of close grained Cast-iron with integral suction and discharge openings.
    Impellers : Enclosed type, construction to suit service requirements. Designed for high efficiency, with moderately steep characteristic. They are precision moulded machined and balanced to eliminate any vibration that might cause wear.
    Shaft : Suitable special steel shaft is incorporated to transmit maximum power at low working stress, without vibration. They are machined to close tolerances.
    Bearings : The shaft is supported on two extra size double ball bearings designed for radial and thrust loads. Both bearings contain grease for long life upto 35,000 operating hours.

    MATERIALS OF CONSTRUCTION FOR COMPONENTS :

    Casing: CI,  NICL, CF8,CF8M,CF3M,CF3NIREGIST D2,DUPLEX- 1A,DUPLEX-4A,DUPLEX -5A,WCB,NI-HARD,ALLOY-20, R-55,HASTALLOY-B,
                  HASTALLOY -C, BRONZE,CA6NM,CA15

    Impeller: CI,  NICL, CF8,CF8M,CF3M,CF3NIREGIST D2,DUPLEX- 1A,DUPLEX-4A,DUPLEX -5A,WCB,NI-HARD,ALLOY-20,  R-55,HASTALLOY-B,
                  HASTALLOY -C, BRONZE,CA6NM,CA15,AL. BR,PH. BR

    Shaft: EN8,EN9,SS410,SS431,SS304,SS316,SS316L,SS317,KMONEL,DUPLEX

    Shaft-Bearings: Cutless rubber, Neoprene, Thordon / EQVILET, Bronze, DEVCO,ORKOT

    Bearing: Antifriction

    Shaft seal:     Gland packing, Mech. Seals

    Base plate: MS, CI,SS304,SS316,SS316L,DUPLEX

    Couplings: CI, Cast steel SS410,SS304,SS316,SS316L,DUPLEX SS

    Material of construction can also be given in any other material required by client.
     
     
     
    Copyright © 2011-2012 Flowmoregroup.com. All Rights Reserved.
    Designed by: Creation Infoways Pvt. Ltd.